Create Account
Search
You are here: TDG Forum  >>  Texas Instruments SOMs and Development Kits  >>  OMAP35x, DM3730, AM3703 Torpedo SOM Development Kit  >>   MMC3, ADC, INT1 and LCD

Technical Discussion Group Forum

This forum is provided for user discussion. While Beacon EmbeddedWorks support staff and engineers participate, Beacon EmbeddedWorks does not guarantee the accuracy of all information within in the Technical Discussion Group (TDG).

The "Articles" forums provide brief Articles written by Beacon EmbeddedWorks engineers that address the most frequently asked technical questions.

To receive email notifications when updates are posted for a Beacon EmbeddedWorks product download, please subscribe to the TDG Forum of interest.

TDG Forum

PrevPrev Go to previous topic
NextNext Go to next topic
Last Post 27 Oct 2010 01:09 AM by  loginreg@gmail.com
MMC3, ADC, INT1 and LCD
 3 Replies
Sort:
You are not authorized to post a reply.
Author Messages
loginreg@gmail.com
New Member
New Member
Posts:


--
19 Oct 2010 04:15 PM
    MMC3

    Am I correct in assuming that the MMC3 signals are the equivalent GPIO17..20/12..13 (mode 2 mux)? This would be useful for our project since GPIO0..31 have special features for interrupting in certain low power states.

    If not, then MMC3 can only otherwise be on GPIO136..139/175..176 (mode 3 mux). This is not so useful, I hope this is not the case.

    ADC

    Is the PMIC START_ADC signal routed to a GPIO on the OMAP?

    INT1

    Is the PMIC INT1 signal routed GPIO0 (sys_nirq) on the OMAP? Or anther GPIO?


    The more I look at the Torpedo board the more I see it as a much better fit than our current OMAP COM, but I just need to check that it supports these things before I can move on. Thanks.

    [edit] I forgot to mention: MMC3 signals for the default board configuration.
    richard.laborde@logicpd.com
    Basic Member
    Basic Member
    Posts:247


    --
    22 Oct 2010 02:56 PM
    Reg - I forwarded your questions on to my HW guy.
    loginreg@gmail.com
    New Member
    New Member
    Posts:


    --
    22 Oct 2010 04:37 PM
    Posted By richardl on 22 Oct 2010 2:56 PM
    Reg - I forwarded your questions on to my HW guy.



    Thank you.
    loginreg@gmail.com
    New Member
    New Member
    Posts:


    --
    27 Oct 2010 01:09 AM
    The names used in the LogicPD docs are confusing me. I hope this table is a little clearer to describe what I can't manage to figure out. Am I also correct in assuming how the three LCD signals below are connected to the OMAP?

    LogicPD name Conn Mux mode 4 Mux mode 1
    -----------------------------------------------------------
    SD3_CLK J1:87 gpio_12 etk_clk
    SD3_CMD J1:99 gpio_13 etk_ctl
    SD3_DATA3 J1:90 gpio_17 etk_d3
    SD3_DATA0 J1:96 gpio_18 etk_d4
    SD3_DATA1 J1:94 gpio_19 etk_d5
    SD3_DATA2 J1:92 gpio_20 etk_d6

    LCD_MDISP J2:16 gpio_152 mcbsp4_clkx
    LCD_BACKLIGHT_PWR J1:75 gpio_154 mcbsp4_dx
    LCD_PANEL_PWR J1:73 gpio_155 mcbsp4_fsx


    All the other names and connections appear to be quite straightforward, matching the mux-mode-0 configuration names from TI. So I think I've got the rest of it prepared for routing and programming.

    Plus I hope I can get the START_ADC and INT1 connections to the PMIC clarified.

    TIA
    You are not authorized to post a reply.

    Forums Texas Instruments SOMs and Development Kits OMAP35x, DM3730, AM3703 Torpedo SOM Development Kit