Search

Technical Discussion Group Forum

This forum is provided for user discussion. While Beacon EmbeddedWorks support staff and engineers participate, Beacon EmbeddedWorks does not guarantee the accuracy of all information within in the Technical Discussion Group (TDG).

The "Articles" forums provide brief Articles written by Beacon EmbeddedWorks engineers that address the most frequently asked technical questions.

To receive email notifications when updates are posted for a Beacon EmbeddedWorks product download, please subscribe to the TDG Forum of interest.

TDG Forum

PrevPrev Go to previous topic
NextNext Go to next topic
Last Post 03 Oct 2016 06:27 AM by  Adam Ford
VM build failed to boot up
 4 Replies
Sort:
You are not authorized to post a reply.
Author Messages
minchun liu
New Member
New Member
Posts:5


--
12 Sep 2013 02:27 PM
    I installed Virtual Machine 2.3 on a Win7 PC. I manually created a folder in rootfs/myFolder and added my application files to it which is about 7MB. The build was fine. The folder was included in the file rootfs.ext2.gz.uboot. But I got Kernel Panic during boot-up, see the attached log. Could anyone tell me how to change the size of rm0?

    If I remove all the files in myFolder and only keep a file with a few KBytes, it can boot up successfully.
    Also the same Kernel Panic happens on VM 2.2.


    =============Message Log================


    Starting kernel ...

    [ 0.000000] Linux version 3.0.0-BSP-dm37x-2.3-2 (root@logic-virtual) (gcc ver
    sion 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #3 Wed Aug 28 01:39:54 CDT 2013
    [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7f
    [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache

    [ 0.000000] Machine: Logic DM37x Torpedo board
    [ 0.000000] debug: ignoring loglevel setting.
    [ 0.000000] Reserving 4194304 bytes SDRAM for VRAM
    [ 0.000000] Memory policy: ECC disabled, Data cache writeback
    [ 0.000000] OMAP3630 ES1.2 (l2cache iva sgx neon isp 192mhz_clk )
    [ 0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x10000
    [ 0.000000] On node 0 totalpages: 64512
    [ 0.000000] free_area_init_node: node 0, pgdat c092b014, node_mem_map c0ece00
    0
    [ 0.000000] Normal zone: 512 pages used for memmap
    [ 0.000000] Normal zone: 0 pages reserved
    [ 0.000000] Normal zone: 64000 pages, LIFO batch:15
    [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/400/600 MHz
    [ 0.000000] Reprogramming SDRC clock to 400000000 Hz
    [ 0.000000] dpll3_m2_clk rate change failed: -22
    [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
    [ 0.000000] pcpu-alloc: [0] 0
    [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64000
    [ 0.000000] Kernel command line: nand-ecc=chip console=ttyO0,115200n8 display
    =15 ignore_loglevel early_printk no_console_suspend mtdparts=omap2-nand.0:512k(x
    -loader),1664k(u-boot),384k(u-boot-env),5m(kernel),20m(ramdisk),-(fs) root=/dev/
    ram rw ramdisk_size=64000
    [ 0.000000] omap3logic_display_selection:265
    [ 0.000000] Standard display '15' 480:272:2:3:3:2:42:11:9000:1048635:16
    [ 0.000000] omap3logic_display_selection: found panel '15'
    [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
    [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
    [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
    [ 0.000000] Memory: 252MB = 252MB total
    [ 0.000000] Memory: 225052k/225052k available, 37092k reserved, 0K highmem
    [ 0.000000] Virtual kernel memory layout:
    [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
    [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
    [ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
    [ 0.000000] vmalloc : 0xd0800000 - 0xf8000000 ( 632 MB)
    [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
    [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
    [ 0.000000] .init : 0xc0008000 - 0xc0045000 ( 244 kB)
    [ 0.000000] .text : 0xc0045000 - 0xc07593d8 (7249 kB)
    [ 0.000000] .data : 0xc075a000 - 0xc0939170 (1917 kB)
    [ 0.000000] .bss : 0xc0939194 - 0xc0ecd4b4 (5713 kB)
    [ 0.000000] NR_IRQS:410
    [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
    [ 0.000000] Total of 96 interrupts on 1 active controller
    [ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz
    [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 13
    1071999ms
    [ 0.000000] Console: colour dummy device 80x30
    [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo
    Molnar
    [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8
    [ 0.000000] ... MAX_LOCK_DEPTH: 48
    [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191
    [ 0.000000] ... CLASSHASH_SIZE: 4096
    [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384
    [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768
    [ 0.000000] ... CHAINHASH_SIZE: 16384
    [ 0.000000] memory used by lock dependency info: 3951 kB
    [ 0.000000] per task-struct memory footprint: 2304 bytes
    [ 0.000823] Calibrating delay loop... 597.64 BogoMIPS (lpj=2334720)
    [ 0.093841] pid_max: default: 32768 minimum: 301
    [ 0.094329] Security Framework initialized
    [ 0.094635] Mount-cache hash table entries: 512
    [ 0.098846] CPU: Testing write buffer coherency: ok
    [ 0.109771] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_core
    [ 0.109802] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_per
    [ 0.109802] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_wkup

    [ 0.110229] omap_hwmod: gpt12_fck: missing clockdomain for gpt12_fck.
    [ 0.141082] print_constraints: dummy:
    [ 0.141479] cpufreq_core_init:1887
    [ 0.142608] NET: Registered protocol family 16
    [ 0.143310] GPMC revision 5.0
    [ 0.147460] omap_device: omap_gpio.0: new worst case activate latency 0: 91552
    [ 0.149597] OMAP GPIO hardware version 2.5
    [ 0.151031] OMAP GPIO hardware version 2.5
    [ 0.152496] OMAP GPIO hardware version 2.5
    [ 0.153900] OMAP GPIO hardware version 2.5
    [ 0.155242] OMAP GPIO hardware version 2.5
    [ 0.156768] OMAP GPIO hardware version 2.5
    [ 0.158935] omap_mux_init: Add partition: #1: core, flags: 0
    [ 0.265930] omap3torpedo_fix_pbias_voltage:1309 PKUP_CTRL 0x40
    [ 0.268066] omap3logic_lcd_init: name 15 data_lines 16
    [ 0.271728] Setup pinmux and enable UART A
    [ 0.272277] omap_device: omap_uart.0: new worst case activate latency 0: 30517
    [ 0.272735] omap_device: omap_uart.0: new worst case deactivate latency 0: 30517
    [ 0.273010] Setup pinmux and enable UART B
    [ 0.274261] Setup pinmux and enable UART C
    [ 0.275604] Minchun: Modified SPIDEV SPI1.0
    [ 0.276733] Minchun: Total SPI ports=8
    [ 0.276794] _omap_mux_init_gpio: Multiple gpio paths (2) for gpio130
    [ 0.276824] _omap_mux_init_gpio: Multiple gpio paths (2) for gpio131
    [ 0.277221] gpio_request: gpio-154 (TxPwr) status -16
    [ 0.277252] !!!ML: Can't allocate GPIO 154
    [ 0.277252] Minchun: ml_gpio_init DONE
    [ 0.277282] arch/arm/mach-omap2/board-omap3logic-new-productid.c[330]
    [ 0.277313] U-boot provided product_id data has invalid header version -22!
    [ 0.277313] No valid product ID data found in SRAM
    [ 0.277496] gpio_request: gpio-152 (wlan_irq) status -16
    [ 0.277526] Failed to gpio_request 152 for wlan_irq
    [ 0.279357] _nand_init: id 0 nand_cs 0
    [ 0.279998] registered isp1763 platform_device
    [ 0.282409] dm3730logic_camera_init: muxing 8-bit interface (cam_d0-cam_d7)
    [ 0.282897] hw-breakpoint: debug architecture 0x4 unsupported.
    [ 0.292907] OMAP DMA hardware revision 5.0
    [ 0.328094] bio: create slab at 0
    [ 0.331787] SCSI subsystem initialized
    [ 0.332672] omap_device: omap2_mcspi.1: new worst case activate latency 0: 30
    517
    [ 0.335906] omap_device: omap2_mcspi.1: new worst case deactivate latency 0:
    30517
    [ 0.340789] usbcore: registered new interface driver usbfs
    [ 0.341186] usbcore: registered new interface driver hub
    [ 0.341674] usbcore: registered new device driver usb
    [ 0.344146] omap_device: omap_i2c.1: new worst case activate latency 0: 30517

    [ 0.344360] omap_i2c omap_i2c.1: bus 1 rev4.0 at 2600 kHz
    [ 0.379577] twl4030: PIH (irq 7) chaining IRQs 368..375
    [ 0.379821] twl4030: power (irq 373) chaining IRQs 376..383
    [ 0.381896] twl4030: gpio (irq 368) chaining IRQs 384..401
    [ 0.385406] machine_constraints_voltage: VUSB1V5: override min_uV, 1 -> 15000
    00
    [ 0.385437] machine_constraints_voltage: VUSB1V5: override max_uV, 2147483647
    -> 1500000
    [ 0.385467] print_constraints: VUSB1V5: 1500 mV normal standby
    [ 0.387145] machine_constraints_voltage: VUSB1V8: override min_uV, 1 -> 18000
    00
    [ 0.387176] machine_constraints_voltage: VUSB1V8: override max_uV, 2147483647
    -> 1800000
    [ 0.387207] print_constraints: VUSB1V8: 1800 mV normal standby
    [ 0.388885] machine_constraints_voltage: VUSB3V1: override min_uV, 1 -> 31000
    00
    [ 0.388916] machine_constraints_voltage: VUSB3V1: override max_uV, 2147483647
    -> 3100000
    [ 0.388946] print_constraints: VUSB3V1: 3100 mV normal standby
    [ 0.394226] twl4030_usb twl4030_usb: Initialized TWL4030 USB module
    [ 0.396362] print_constraints: vdd_mpu_iva: 600 <--> 1450 mV normal
    [ 0.398345] print_constraints: vdd_core: 600 <--> 1450 mV normal
    [ 0.400512] print_constraints: VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby
    [ 0.402282] print_constraints: VDAC: 1800 mV normal standby
    [ 0.404144] print_constraints: VDVI: 1800 mV normal standby
    [ 0.405944] print_constraints: VMMC2: 1850 <--> 3150 mV at 2600 mV normal standby
    [ 0.407836] print_constraints: VAUX1: 3000 mV normal standby
    [ 0.409912] print_constraints: VAUX3: 2800 mV normal standby
    [ 0.411773] print_constraints: vaux4: 1800 mV normal standby
    [ 0.412506] omap_device: omap_i2c.1: new worst case deactivate latency 0: 30517
    [ 0.412872] omap_i2c omap_i2c.2: bus 2 rev4.0 at 400 kHz
    [ 0.413787] omap_device: omap_i2c.1: new worst case activate latency 0: 61035

    [ 0.422088] omap_i2c omap_i2c.3: bus 3 rev4.0 at 400 kHz
    [ 0.424865] Advanced Linux Sound Architecture Driver Version 1.0.24.
    [ 0.427429] Bluetooth: Core ver 2.16
    [ 0.427673] NET: Registered protocol family 31
    [ 0.427673] Bluetooth: HCI device and connection manager initialized
    [ 0.427795] Bluetooth: HCI socket layer initialized
    [ 0.427825] Bluetooth: L2CAP socket layer initialized
    [ 0.428466] Bluetooth: SCO socket layer initialized
    [ 0.430816] cfg80211: Calling CRDA to update world regulatory domain
    [ 0.435058] Switching to clocksource 32k_counter
    [ 0.437896] Switched to NOHz mode on CPU #0
    [ 0.568908] musb-hdrc: version 6.0, musb-dma, otg (peripheral+host)
    [ 0.569427] omap_device: musb-omap2430.-1: new worst case activate latency 0: 30517
    [ 0.577301] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
    [ 0.577331] musb-hdrc: MHDRC RTL version 1.800
    [ 0.577362] musb-hdrc: setup fifo_mode 4
    [ 0.577362] musb-hdrc: 28/31 max ep, 16384/16384 memory
    [ 0.578155] musb-hdrc musb-hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92
    [ 0.579101] NET: Registered protocol family 2
    [ 0.579681] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
    [ 0.581481] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
    [ 0.581909] TCP bind hash table entries: 8192 (order: 6, 360448 bytes)
    [ 0.586486] TCP: Hash tables configured (established 8192 bind 8192)
    [ 0.586547] TCP reno registered
    [ 0.586608] UDP hash table entries: 128 (order: 1, 12288 bytes)
    [ 0.586944] UDP-Lite hash table entries: 128 (order: 1, 12288 bytes)
    [ 0.588134] NET: Registered protocol family 1
    [ 0.590209] RPC: Registered named UNIX socket transport module.
    [ 0.590240] RPC: Registered udp transport module.
    [ 0.590240] RPC: Registered tcp transport module.
    [ 0.590270] RPC: Registered tcp NFSv4.1 backchannel transport module.
    [ 0.590362] NetWinder Floating Point Emulator V0.97 (double precision)
    [ 0.590942] added int user_gpio_init_module () registed
    [ 0.593811] omap-iommu omap-iommu.0: isp registered
    [ 0.777008] Trying to unpack rootfs image as initramfs...
    [ 0.780609] rootfs image is not initramfs (no cpio magic); looks like an initrd
    [ 0.782958] VFS: Disk quotas dquot_6.5.2
    [ 0.783050] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    [ 0.785736] JFFS2 version 2.2. (NAND) (SUMMARY) 2001-2006 Red Hat, Inc.
    [ 0.786468] yaffs: yaffs built Jan 17 2013 15:45:13 Installing.
    [ 0.786590] msgmni has been set to 439
    [ 0.793670] omap_device: musb-omap2430.-1: new worst case deactivate latency0: 61035
    [ 0.796112] io scheduler noop registered
    [ 0.796142] io scheduler deadline registered
    [ 0.796295] io scheduler cfq registered (default)
    [ 0.798767] Generic Backlight Driver Initialized.
    [ 0.857330] OMAP DSS rev 2.0
    [ 0.866027] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
    [ 0.883972] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP UART0
    [ 1.977172] console [ttyO0] enabled
    [ 2.026794] Freeing initrd memory: 15532K
    [ 2.031799] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP UART1
    [ 2.040466] omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a OMAP UART2
    [ 2.072448] brd: module loaded
    [ 2.087463] loop: module loaded
    [ 2.095550] mtdoops: mtd device (mtddev=name/number) must be supplied
    [ 2.102783] omap2-nand driver initializing
    [ 2.108184] nand_get_flash_type: disturb ce280000 chipsize 536870912 erasesize 131072
    [ 2.116485] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xbc (Micron NAND 512MiB 1,8V 16-bit)
    [ 2.125640] NAND ECC: HW_CHIP
    [ 2.128814] 6 cmdlinepart partitions found on MTD device omap2-nand.0
    [ 2.135650] Creating 6 MTD partitions on "omap2-nand.0":
    [ 2.141326] 0x000000000000-0x000000080000 : "x-loader"
    [ 2.153137] 0x000000080000-0x000000220000 : "u-boot"
    [ 2.163543] 0x000000220000-0x000000280000 : "u-boot-env"
    [ 2.172851] 0x000000280000-0x000000780000 : "kernel"
    [ 2.186248] 0x000000780000-0x000001b80000 : "ramdisk"
    [ 2.213439] 0x000001b80000-0x000020000000 : "fs"
    [ 2.677093] smsc911x: Driver version 2008-10-21
    [ 2.687866] smsc911x-mdio: probed
    [ 2.691772] smsc911x smsc911x.0: eth0: attached PHY driver [SMSC LAN8700] (mii_bus:phy_addr=0:01, irq=-1)
    [ 2.703857] smsc911x smsc911x.0: eth0: MAC Address: 86:3b:b9:2f:ab:7a
    [ 2.711334] usbcore: registered new interface driver asix
    [ 2.717254] usbcore: registered new interface driver cdc_ether
    [ 2.723541] usbcore: registered new interface driver net1080
    [ 2.729705] usbcore: registered new interface driver cdc_subset
    [ 2.736145] usbcore: registered new interface driver zaurus
    [ 2.742065] cdc_ncm: 01-June-2011
    [ 2.745758] usbcore: registered new interface driver cdc_ncm
    [ 2.751770] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [ 2.759399] devflags passed by probe: 0x00000004
    [ 2.794616] hwmode pullup disable
    [ 2.798095] Error: ISP1763 chip ID wrong! (14011401, expected 00176320)
    [ 2.805084] ISP1783 using host mode
    [ 2.808746] otg_set_role() switching to HOST role
    [ 2.813751] isp1763 initialization successfully
    [ 2.818542] ISP1763 USB device initialised
    [ 2.823181] Registered host as active driver
    [ 2.827728] isp1763 isp1763: ST-Ericsson ISP1763 USB Host Controller
    [ 2.836151] isp1763 isp1763: new USB bus registered, assigned bus number 1
    [ 3.480407] isp1763 isp1763: can't setup
    [ 3.484558] isp1763 isp1763: USB bus 1 deregistered
    [ 3.492156] isp1763 host controller driver loaded
    [ 3.497100] Initializing USB Mass Storage driver...
    [ 3.502624] usbcore: registered new interface driver usb-storage
    [ 3.509002] USB Mass Storage support registered.
    [ 3.514129] usbcore: registered new interface driver usbtest
    [ 3.521270] mousedev: PS/2 mouse device common for all mice
    [ 3.530059] gpio_request: gpio-153 (tsc2004-irq) status -16
    [ 3.535919] failed to request GPIO#153: -16
    [ 3.543426] tsc2004: probe of 3-0048 failed with error -121
    [ 3.549530] i2c-core: driver [tsc2004] using legacy resume method
    [ 3.558013] input: twl4030_pwrbutton as /devices/platform/omap/omap_i2c.1/i2c-1/1-0049/twl4030_pwrbutton/input/input0
    [ 3.577972] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
    [ 3.584838] twl_rtc twl_rtc: Power up reset detected.
    [ 3.590972] twl_rtc twl_rtc: Enabling TWL-RTC.
    [ 3.596527] i2c /dev entries driver
    [ 3.602722] Linux media interface: v0.10
    [ 3.607757] lirc_dev: IR Remote Control driver registered, major 250
    [ 3.614624] IR NEC protocol handler initialized
    [ 3.619445] IR RC5(x) protocol handler initialized
    [ 3.624542] IR RC6 protocol handler initialized
    [ 3.629302] IR JVC protocol handler initialized
    [ 3.634094] IR Sony protocol handler initialized
    [ 3.639007] IR RC5 (streamzap) protocol handler initialized
    [ 3.644866] IR LIRC bridge handler initialized
    [ 3.649566] Linux video capture interface: v2.00
    [ 3.656036] omap3isp omap3isp: Revision 15.0 found
    [ 3.661376] omap-iommu omap-iommu.0: isp: version 1.1
    [ 3.685577] ov7690 3-0021: OV7690 not detected, wrong manufacturer or version
    [ 3.695312] isp_register_subdev_group: Unable to register subdev ov7690
    [ 3.704467] mt9p031 2-0048: MT9P031 not detected, wrong version 0xffffff87
    [ 3.712371] isp_register_subdev_group: Unable to register subdev mt9p031
    [ 3.723754] usbcore: registered new interface driver uvcvideo
    [ 3.729888] USB Video Class driver (v1.1.0)
    [ 3.735015] omap_device: omap_wdt.-1: new worst case activate latency 0: 30517
    [ 3.743743] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
    [ 3.750183] omap_device: omap_wdt.-1: new worst case deactivate latency 0: 30517
    [ 3.760711] cpuidle: using governor ladder
    [ 3.765106] cpuidle: using governor menu
    [ 3.777557] Registered led device: led1
    [ 3.782196] Registered led device: led2
    [ 3.791076] Registered led device: led3
    [ 3.796936] usbcore: registered new interface driver usbhid
    [ 3.802856] usbhid: USB HID core driver
    [ 3.808990] usbcore: registered new interface driver snd-usb-audio
    [ 3.820098] OMAP3 Logic DM37x/OMAP35x SOM LV/Torpedo SoC init
    [ 3.926605] asoc: twl4030-hifi <-> omap-mcbsp-dai.1 mapping ok
    [ 3.938629] ALSA device list:
    [ 3.941741] #0: omap3logic
    [ 3.944854] oprofile: hardware counters not available
    [ 3.950164] oprofile: using timer interrupt.
    [ 3.954864] nf_conntrack version 0.5.0 (3759 buckets, 15036 max)
    [ 3.963073] ip_tables: (C) 2000-2006 Netfilter Core Team
    [ 3.969512] TCP cubic registered
    [ 3.972930] Initializing XFRM netlink socket
    [ 3.977661] NET: Registered protocol family 17
    [ 3.982513] NET: Registered protocol family 15
    [ 3.987823] Bluetooth: RFCOMM TTY layer initialized
    [ 3.993103] Bluetooth: RFCOMM socket layer initialized
    [ 3.998565] Bluetooth: RFCOMM ver 1.11
    [ 4.002471] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
    [ 4.008178] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
    [ 4.015289] Registering the dns_resolver key type
    [ 4.020965] VFP support v0.3: implementor 41 architecture 3 part 30 variant c
    rev 3
    [ 4.029144] ThumbEE CPU extension supported.
    [ 4.058471] smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver initialized
    [ 4.068511] smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver initialized
    [ 4.077514] SmartReflex Class3 initialized
    [ 4.081817] sr_start_vddautocomp: sr->srid 1
    [ 4.086486] omap_device: smartreflex.1: new worst case activate latency 0: 122070
    [ 4.094451] sr_start_vddautocomp: sr->srid 0
    [ 4.160461] clock: disabling unused clocks to save power
    [ 4.177185] Console: switching to colour frame buffer device 60x34
    [ 4.475616] smartreflex smartreflex.0: sr_v2_disable: Smartreflex disable timedout
    [ 4.484222] omap_device: smartreflex.0: new worst case deactivate latency 0:152587
    [ 4.529144] mmc0: host does not support reading read-only switch. assuming write-enable.
    [ 4.538085] mmc0: new SDHC card at address 0007
    [ 4.547485] mmcblk0: mmc0:0007 SL04G 3.70 GiB
    [ 4.566253] mmcblk0: p1
    [ 4.624298] omap_device: omap_i2c.1: new worst case activate latency 0: 152587
    [ 4.632751] regulator_init_complete: VAUX3: incomplete constraints, leaving on
    [ 4.642272] regulator_init_complete: VDAC: incomplete constraints, leaving on
    [ 4.656402] twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:01 UTC(946684801)
    [ 4.665802] omap_vout omap_vout: Buffer Size = 3686400
    [ 4.675323] omap_vout omap_vout: : registered and initialized video device 15
    [ 4.683105] omap_vout omap_vout: Buffer Size = 3686400
    [ 4.690979] omap_vout omap_vout: : registered and initialized video device 16

    [ 4.707519] RAMDISK: gzip image found at block 0
    [ 4.827575] dm3730_torpedo_bl_set_intensity: level 178 (69% on)
    [ 4.834014] dm3730_torpedo_bl_set_intensity: turn on GPIO_154 as backlight!
    [ 5.100616] smartreflex smartreflex.0: sr_v2_disable: Smartreflex disable tim
    edout
    [ 7.186401] RAMDISK: incomplete write (2037 != 10663)
    [ 7.191711] write error
    [ 7.664123] VFS: Mounted root (ext2 filesystem) on device 1:0.
    [ 7.670593] Freeing init memory: 244K
    [ 7.678039] attempt to access beyond end of device
    [ 7.683044] ram0: rw=0, want=134412, limit=128000
    [ 7.688232] Buffer I/O error on device ram0, logical block 67205
    [ 7.694610] attempt to access beyond end of device
    [ 7.699615] ram0: rw=0, want=134502, limit=128000
    [ 7.704559] Buffer I/O error on device ram0, logical block 67250
    [ 7.710906] attempt to access beyond end of device
    [ 7.715911] ram0: rw=0, want=134412, limit=128000
    [ 7.720886] Buffer I/O error on device ram0, logical block 67205
    [ 7.727203] attempt to access beyond end of device
    [ 7.732269] ram0: rw=0, want=134502, limit=128000
    [ 7.737182] Buffer I/O error on device ram0, logical block 67250
    [ 7.745391] Kernel panic - not syncing: No init found. Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.
    [ 7.758544] [] (unwind_backtrace+0x0/0x138) from [] (panic+0x6c/0x1a4)
    [ 7.767272] [] (panic+0x6c/0x1a4) from [] (init_post+0xf8/0x154)
    [ 7.775421] [] (init_post+0xf8/0x154) from [] (kernel_init+0x124/0x13c)
    [ 7.784210] [] (kernel_init+0x124/0x13c) from [] (kernel_thread_exit+0x0/0x8)

    ==============End of Log ===============
    steven.eckhoff
    Basic Member
    Basic Member
    Posts:192


    --
    24 Sep 2013 10:12 AM
    Minchun,

    Have you tried this using NAND and a YAFFS filesystem?
    minchun liu
    New Member
    New Member
    Posts:5


    --
    15 Oct 2013 02:08 PM
    Steven

    I haven't tried NAND or YAFFS yet. But with the latest 2.4-2 VM, the issue seems fixed.

    Thanks,

    Minchun
    Mark Gregory
    New Member
    New Member
    Posts:9


    --
    02 Oct 2016 11:04 AM

    I am having a similar issue when adding additional packages and booting from an SD card. After building the image on my host machine it compiles fine but it gives me a blurb about setting boot args to increase ramdisk_size.  I have increased the ramdisk_size to the value recommended and it still fails to boot.  I added make only and it booted fine.  Then I recompiled adding git and gdb (running on target) with make and it fails.  

    This seems to be the primary point of failure:

    [    6.925598] RAMDISK: incomplete write (18872 != 32768)
    [    6.931060] write error
    [    7.322540] VFS: Mounted root (ext2 filesystem) on device 1:0.
    [    7.328979] Freeing init memory: 244K
    [    7.333862] EXT2-fs (ram0): error: ext2_get_inode: unable to read inode block - inode=2009, block=73390
    [    7.343750] EXT2-fs (ram0): error: remounting filesystem read-only
    [    7.350891] EXT2-fs (ram0): error: ext2_get_inode: unable to read inode block - inode=2648, block=97847
    [    7.360778] EXT2-fs (ram0): error: remounting filesystem read-only
    [    7.367431] EXT2-fs (ram0): error: ext2_get_inode: unable to read inode block - inode=2009, block=73390
    [    7.377319] EXT2-fs (ram0): error: remounting filesystem read-only
    [    7.384002] EXT2-fs (ram0): error: ext2_get_inode: unable to read inode block - inode=2009, block=73390
    [    7.393890] EXT2-fs (ram0): error: remounting filesystem read-only
    [    7.400451] Kernel panic - not syncing: No init found.  Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.

     

     

         

    Adam Ford
    Advanced Member
    Advanced Member
    Posts:794


    --
    03 Oct 2016 06:27 AM
    Can you post the beginning of the boot log where it displays the ramdisk size? I want to see what it says.

    How big did ltib say the image was?

    adam
    You are not authorized to post a reply.