Hi Aaron,
I have already looked at that thread. My partitions are the same as the ones in the document. Unless the device is mounted under a different name than hda, I think I am mounting the right partition. Folllowing is all the output I see plus some of my last commands before booting:
losh> mount fatfs /f
losh> cd /f
losh> load elf VMLINUX
loading from /f/VMLINUX:
R...........
elf file type : 0x0002
machine type: 0028 version: 1
prog start addr : 0x200c8000
num prog headers: 1
num sect headers: 10
offset : 0x00008000 disk length: 0x00157c73 mem len: 0x0017f39c
phyaddr: 0x200c8000 vaddr : 0x200c8000 dl addr: 0x200c8000
losh> exec root=/dev/hda1
kernel cmdline: 'root=/dev/hda1' at 200c0100
jumping to: 200c8000...
Linux version 2.4.17-rmk2-lineo5 (
root@lpd079lnx.logicpd.com) (gcc version 2.953Processor: ARM ARM720T revision 3
Architecture: LogicPD LH79520 Card Engine
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyAM1,115200 root=/dev/hda1
setup_timer(): timerLoad=32256
Console: colour dummy device 80x30
Calibrating delay loop... 25.65 BogoMIPS
Memory: 32MB = 32MB total
Memory: 14288KB available (1206K code, 250K data, 76K init)
Dentry-cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode-cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
ttyAM0 at MEM 0xfffc0000 (irq = 23) is a AMBA PrimeCell PL011
ttyAM1 at MEM 0xfffc1000 (irq = 24) is a AMBA PrimeCell PL011
ttyAM2 at MEM 0xfffc2000 (irq = 25) is a AMBA PrimeCell PL011
Console: switching to colour frame buffer device 30x40
LH79520 Watchdog Timer: timer margin 60 sec
block: 64 slots per queue, batch=16
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
hd: no drives specified - use hd=cyl,head,sectors on kernel command line
hd?: check_status: status=0xd0 { Busy DriveReady SeekComplete }
hda: 61MB, CHS=978/4/32
Partition check:
hda:hda: check_status: status=0xd0 { Busy DriveReady SeekComplete }
hda1 hda2
eth0: SMC91C11xFD(rev:1) at 0xf4800000 IRQ:4 DMA:0 (16-bit) MEM:8192b NOWAIT:1
eth0: ADDR: 00:08:ee:00:12:1f
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 2048)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NetWinder Floating Point Emulator V0.95 (c) 1998-1999 Rebel.com
RAMDISK: Couldn't find valid RAM disk image starting at 0.
Freeing initrd memory: 16384K
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
Freeing init memory: 76K
Warning: unable to open an initial console.
Kernel panic: No init found. Try passing init= option to kernel.
Thanks.
Talat,