I have Windows CE.Net 4.2 and installed both the LOCE_A400_Beta_001 and the 002 .
Here is the serial output from the session:
*****************************************************************
LogicLoader
(c) Copyright 2002-2003, Logic Product Development, Inc.
All Rights Reserved.
Version 1.2.3
*****************************************************************
Available commands:
load - download a binary image of type 'elf', or 'srec'
burn - burns the already-loaded image into flash device 'device'
erase - erases 'device' from start_address for length bytes
jump - jump to a loaded image, or [address]
exec - disable cache & ints, then jump to a loaded OS, or to [addr]
source - execute a series of losh commands stored in <filename>
w - write memory [of specified width] at addr
x - examine memory with [width][format] at an addr for a [len]
date - display the number of seconds since boot
info - print information about: version, arch, mem, net, cpu
help - print help for a single command or a group of commands.
losh> bootme &
Blosh> OOTME: no active network interfaces. Try ifconfig
losh> ifconfig sm0 dhcp
MAC Address: 00:08:ee:00:14:7e
MAC Address: 00:08:ee:00:14:7e
Starting DHCP on sm0
losh> ifconfig
sm0: up 100M half-duplex (415)
sm0: mac: 0:8:ee:0:14:7e ip: 192.168.1.106
mask: 255.255.255.0 gw: 192.168.1.1
losh> bootme &
losh>
Device's name is LoCE_5246.
Sent BOOTME
Sent BOOTME
Sent BOOTME
Sent BOOTME
Got a response from a host ip: 192.168.1.102 port: 3107
Connecting to Platform Builder
R
image launch addr: 0xc00e1000
Verifying checksums: >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
Checksums good.
BOOTME: Got jump command
losh> source /dev/serial_eeprom
losh> exec dbg_serial:A400_UART:dbg_enet:91C111:dbg_enet_base:0x70000000:rtc:rtc
_a400_int:share_eth:1
kernel cmdline: 'dbg_serial:A400_UART:dbg_enet:91C111:dbg_enet_base:0x70000000:r
tc:rtc_a400_int:share_eth:1:kitl:true:ip_addr:192.168.1.106' at c00c0100
disabling mmu.
LoCE start
link_for_flash: 0
Debug serial initialized. Using driver A400_UART
Windows CE Kernel for ARM (Thumb Enabled) Built on Jul 25 2003 at 11:54:05
ProcessorType=0922 Revision=0
sp_abt=ffff5000 sp_irq=ffff2800 sp_undef=ffffc800 OEMAddressTable = 800e1220
===================================================================
WinCE firmware init (LoCE).
Kernel Arguments: dbg_serial:A400_UART:dbg_enet:91C111:dbg_enet_base:0x70000000:
rtc:rtc_a400_int:share_eth:1:kitl:true:ip_addr:192.168.1.106.
image_size: 0xF00000
ram_size: 0xC00000
link_for_flash: 0
===================================================================
Initializing interrupts.
Interrupt initialization complete.
Initializing system-tick.
System-tick initialized.
RTC initialized. Using driver rtc_a400_int
Multiple XIP regions not defined or fixup failed.
Initializing KITL.
Remote host present.
Debug enet initialized. Using driver 91C111
Debug enet base read as 0x70000000
Debug enet base mapped to virtual address 0xBFE00000.
hooking platform interrupts... done
OEMKitlInit()
SmSC Ethernet controller detected: 0xBFE00000
MAC Address: 00:08:EE:00:14:7E
91C111: 100 Mbits half-duplex.
+pckt_list_init(): 0x80002000 : 0x00002800
Device Name: LoCE_5246, IP: 192.168.1.106, Port: 981
KITL Buffers at 0x80005000 len 0x20000
KITL Interrupt using SysIntr: 16.
share_dbg_enet read as 0x00000001
Initializing VBridge.
VBridgeInit()...TX = [16384] bytes -- Rx = [16384] bytes
Tx buffer [0xA102F0C0] to [0xA10330C0].
Rx buffer [0xA102B0A0] to [0xA102F0A0].
VBridge:: NK add MAC: [0-8-EE-0-14-7E]
VBridge initialized.
KITL Ethernet transport initialized
Host connected.
Host IP: 192.168.1.102, port 3106
KeyIndex 0 = -1
KeyIndex 1 = -1
KeyIndex 2 = -1
KeyIndex 3 = -1
KeyIndex 4 = -1
KeyIndex 5 = -4194305
KeyIndex 6 = -4194305
KeyIndex 7 = -1
+KITLRegisterDfltClient, service:0
+KITLRegisterDfltClient, service:1
KITLGlobalState == 0x61
KITL initialized.
Firmware initialization complete.
driver globals at 0x80000000.
Waiting for service 'DBGMSG' to connect..., fUseSysCalls = 0
ProcessAdminMsg: Receive Config message for service DBGMSG
ProcessAdminMsg: Receive Config message for service PPSH
ProcessAdminMsg: Receive Config message for service DBGMSG
ProcessAdminMsg: Receive Config message for service PPSH
ProcessAdminMsg: Receive Config message for service DBGMSG
ARMInit done.
+KITLRegisterDfltClient, service:2
ProcessAdminMsg: Receive Config message for service KDBG
ProcessAdminMsg: Receive Config message for service KDBG
KITL: Leaving polling mode...
KITL Checking client registrations
+RegisterClientPart2: Id 0x00000000
KITL Timer thread started, (hTh: 0x01BFFF86, pTh: 0x81BFCAF8)
-RegisterClientPart2
+RegisterClientPart2: Id 0x00000001
-RegisterClientPart2
KITL Creating IST
KITL Interrupt thread started (hTh: 0xC1BEF9F2, pTh: 0x81BEF7B4), using SYSINTR
16
Enabling adapter ints...
Enabling debug ethernet interrupts.
Enabling SmSC 91C111 receive interrupt.[list=][/list][/list]
|