I am trying to test a "release" version of my platform by building "release" version and then just loading it into ram via logic loader but when I do this it runs very slow.
Here is the output from logic loader
LogicLoader
(c) Copyright 2002-2005, Logic Product Development, Inc.
All Rights Reserved.
Version 2.0.3-LLH7a400_10 0001
*****************************************************************
losh>
losh> ifconfig sm0 dhcp
Starting DHCP on sm0
losh> bootme &
losh>
Device's name is LoCE_18311.
Sent BOOTME 4
Got response from a host ip: 192.168.1.5 port: 1184 cmd: 98
Connecting to Platform Builder
R
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
..............
image launch addr: 0xc00e1000
Verifying checksums: >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>
Checksums good.
BOOTME: loaded
BOOTME: Got jump command
losh> source /dev/serial_eeprom
exec dbg_serial:A400_UART:dbg_enet:91C111:dbg_enet_base:0x70000000:dbg_enet_irq:
0x00000007:kitl:true:rtc:rtc_a400_int:share_eth:kernel cmdline: 'dbg_serial:A400
_UART:dbg_enet:91C111:dbg_enet_base:0x70000000:dbg_enet_irq:0x00000007:kitl:true
:rtc:rtc_a400_int:share_eth::ip_addr:192.168.1.4' at c0058314
Debug serial initialized. Using driver A400_UART
Windows CE Kernel for ARM (Thumb Enabled) Built on Jun 24 2004 at 18:25:00
ProcessorType=0922 Revision=0
sp_abt=ffff5000 sp_irq=ffff2800 sp_undef=ffffc800 OEMAddressTable = 800e1294
==============================================================
WinCE firmware init (LoCE)
Kernel Arguments: "dbg_serial:A400_UART:dbg_enet:91C111:dbg_enet_base:0x70000
000:dbg_enet_irq:0x00000007:kitl:true:rtc:rtc_a400_int:share_eth::ip_addr:192.16
8.1.4"
image_size: 0xF00000
ram_size: 0xC00000
link_for_flash: 0
relocate_from_flash: 0
rom_offset: 0x40000000
==============================================================
Cold-boot: erasing object store.
Initializing interrupts.
Card Engine Rev-B (or later).
CPLD Revision 0x34.
Interrupt initialization complete.
Initializing system-tick.
System-tick initialized.
RTC initialized. Using driver rtc_a400_int.
Multiple XIP regions not defined or fixup failed.
Initializing KITL.
debug_ether: using driver 91C111.
debug_ether: using address 0xB0100000.
debug_ether: using irq 7.
OEMKitlInit()
SmSC Ethernet controller detected: 0xB0100000
MAC Address: 00:08:EE:00:47:87
91C111: 100 Mbits full-duplex.
+pckt_list_init(): 0x80002000 : 0x00002800
Device Name: LoCE_18311, IP: 192.168.1.4, Port: 981.
KITL Buffers at 0x80005000 len 0x20000
KITL Interrupt using SysIntr: 16, Irq: 7.
share_dbg_enet read as 0x00000000
Not sharing the debug Ethernet.
KITL Ethernet transport initialized.
!Kitl buffer specified by OAL is not required, ignore...
Host connected.
Host IP: 192.168.1.5, port 1183
KITLGlobalState == 0x61
KITL initialized.
driver globals at 0x80000000.
Firmware initialization complete.
"link_for_flash" variable says we are in SDRAM.
Detected extension DRAM at 0x84000000, size is 0x02000000
Total RAM installed is 64 MB.
KITL: Leaving polling mode...
Enabling KITL Interrupt.
Enabling SmSC 91C111 receive interrupt.
I am wondering about the "link_for_flash" statement and if it is a problem what I need to do to fix it. Thanks - Frank T.