|
|
|
|
|
|
1 Replies and 3391 Views
32 bit access on lh524 on external connector 3391 1
Started by sreedhar
Hi,
I am trying to port code from lh520 to lh524 and need to read from a 32bit io resource.
In the lh520 board, Video_nCS was available and worked for 32 bit access at address 0x44000000
In lh524, I could not see how to get Video to work. So, I am trying both
fast_nmcs and slow_nmcs signals to access the same 32 bit resource
on my application board ( custom ). The moment I switch the configuration of the SMC
to 32 bit, the board quits getting either of the chip selects.
Can someone clarify ...
|
|
|
|
1 |
3391 |
by Kevin Darmasaputra 22 Nov 2017 01:34 PM |
|
0 Replies and 1810 Views
LH79524 Card Engine .DSN and .MAX 1810 0
Started by Kevin Darmasaputra
Hi, Is LH79524 Card Engine .DSN and .MAX available anywhere In the support website they only have .DSN and .MAX for the SDK app board. Any help will be greatly appreciated. Thank you
|
|
|
|
0 |
1810 |
17 Nov 2016 06:53 PM |
|
6 Replies and 2956 Views
how to register legacy product 2956 6
Started by Deleted User
i have 6 new sets of the zoom sdk with nxp lh79524 from e-bay. I try to register the first of these sets on your site, but the type is not longer listed in the drop down box. Without registering I can't download all the packages i would need for hardware pinout information and also the software is missing . can you help me please to figure out, what i should do thank you for the service Best Regards
|
|
|
|
6 |
2956 |
by Kevin Darmasaputra17 Nov 2016 12:44 PM |
|
1 Replies and 2768 Views
Linux bootloader 2768 1
Started by Deleted User
Hi,
I want to up and run Linux on my LH79524 board. i need Zimage for same but i didn't get. even i didn't got any patch for kernel. &91b&93(zImage-lpd79524)&91/b&93
Please help me to solve this problem.
|
|
|
|
1 |
2768 |
by Deleted User29 Sep 2011 08:29 AM |
|
0 Replies and 2633 Views
LH79525 - JTAG Communication using IAR 2633 0
Started by steveli
Hi,
We have a Board on LH79525 and using IAR debugger. When we tried to download code using J-Link, we are getting some warning messages as shown below :
Tue Aug 31 16:06:53 2010: JLINK command: ProjectFile = D:\Project 350\Firmware\100826_Project350_CSDES Program\settings\
BasicLcd_DebugRunFromFlash.jlink, return = 0
Tue Aug 31 16:06:53 2010: JLINK command: device = LH79525, return = 0
Tue Aug 31 16:06:53 2010: DLL version: V4.14i, compiled Aug 12 2010 20:19:20
Tue Aug 31 16:06:53 2010: Fi...
|
|
|
|
0 |
2633 |
06 Sep 2010 04:49 AM |
|
0 Replies and 2392 Views
LH79524 LCD display 2392 0
Started by steveli
Hi,
We are working on Programming for NXP – LH79524 EVB. We also bought LH79524 Zoom SDK (SDK-LH79524-10-3216R) from Logic PD (http://www.logicpd.com/products/develop ... 84A2-sdk).
We have downloaded Sample program from NXP website – Basic LCD display and could display on Sharp LCD. But there is some problem with display. It is repeating at bottom & right side. The sample image is not fitting into entire LCD screen. How to resolve this Can anyone has problem like this
Also Can anyo...
|
|
|
|
0 |
2392 |
15 Jul 2010 12:51 AM |
|
2 Replies and 2328 Views
Display not listed!! 2328 2
Started by kaursat
We are using the 3.6" Sharp Display - LQ036Q1DA01. However, help video-open doesnot list our display. Please suggest.
In the user manual under the Video section, it says we can save upto 8 LCD settings by using the 'config' command with 'V' option.
It then says: To store the custom setting, "we need to set up the controller".
How do I set up the controller
Below is the portion from the manual for reference. Kindly comment.
Video:
A customer may save up to eight custom LCD ...
|
|
|
|
2 |
2328 |
by Mswinny09 Sep 2008 04:28 AM |
|
1 Replies and 2668 Views
LH79524/79525 memory 2668 1
Started by nambinhngo
Hi all,
I need some help.
I am currently working on the project which utilizes the LH79525 MCU.
I designed my own board, which used SRAM instead of SDRAM comparing to the logic sdk79524 eval board.
the SRAM is mapped on CS0 location 0x40000000, and the flash is at 0x44000000.
I loaded the startup program from the BSP package, and the unit did not initialize at all.
I tried the led_flasher examples and added the memory-init, clock init, gpio, and iomux. the unit initialized such as CLKOUT = HCLK...
|
|
|
|
1 |
2668 |
by nambinhngo08 Sep 2008 04:30 PM |
|
0 Replies and 2562 Views
Keil JTAG cannot download code to LH79524 2562 0
Started by steveh_iniche
Hi,
I am using Keil uVision3 3.62c IDE to develop a standalone application for the LH79524 eval board.
I am using the ULINK-ME JTAG interface. I cannot download code to either the SDRAM at 0x20000000
or the SRAM at 0x44000000. All I get is either "Full Chip Erase Failed!" or "Erase Failed!".
Build target 'Target 1'
linking...
Program Size: Code=113944 RO-data=3952 RW-data=3860 ZI-data=12556
".\obj\nichelite.axf" - 0 Error(s), 0 Warning(s).
Full Ch...
|
|
|
|
0 |
2562 |
09 Jul 2008 07:57 PM |
|
0 Replies and 2398 Views
Logic Loader for LH79525 2398 0
Started by nambinhngo
I am using the LH79525 for me new design. Will Lolo be compatible with the LH79525
|
|
|
|
0 |
2398 |
26 Jun 2008 11:35 AM |
|
5 Replies and 3933 Views
IAR JTAG Cannot Talk to NXP LH79524 3933 5
Started by dwills
Hi,
For some reason, my JTAG cannot connect to the ARM. The J-Trace recognizes board power but not the chip.
The starter kit baseboard quick start guide shows n/a for the jumper settings on J6. I assume this means no jumpers, but I tried all combinations of jumpers on J6 and none work.
Both the J-Trace and the Zoom starter kit are new out of the box, so it's unlikely either is bad.
Anyone have any ideas of what I might try next
Thanks,
Dave
|
|
|
|
5 |
3933 |
by addyyang03 Jun 2008 02:53 PM |
|
1 Replies and 2655 Views
issue when mount fatfs /cf in logic loader 2655 1
Started by addyyang
i got a 'bad partition magic (00 00)' error...
please advice...thanks!
losh> mount fatfs /cf
read_partition_info: bad partition magic (00 00)
0x200441fc 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
0x2004420c 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
0x2004421c 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
0x2004422c 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
0x2004423c 00 00 00 00 00 00 00 00 00 0...
|
|
|
|
1 |
2655 |
by addyyang03 Jun 2008 02:51 PM |
|
0 Replies and 2179 Views
Adding extra serial ports using quad UART device 2179 0
Started by colin324
I have added 4 serial ports to the LH79254 card, using the ST16C554A Quad UART. Using SLOW_nMCS, nIOWR, nIORD, address and data lines I can sometimes get data onto the scratchpad in the UART, sometimes I can read it back too. The issue I have is that sometimes both the nIOWR and nIORD lines seem to both occur together. Do I need any further control lines I am using the memory area 0x4900 0000 – 0x49FF FFFF, as the technical info states for my IO.
|
|
|
|
0 |
2179 |
05 Dec 2007 08:57 AM |
|
1 Replies and 2484 Views
SHARP LH79525 & SAMSUNG K9F1G08U0A 2484 1
Started by Deleted User
Hello, LOGICPD!
==========
With standart configuration of &91LH79524 Zoom Starter Development Kit&93 in SEGGER JTAG SOFTWARE used following initialization of CPU SHARP LH79524 and flash SHARP LH28F128SPHTD-PTL12.
========================================================
01) Action "Reset startup" by address &910x00000000&93 write value &910x00000000&93.
02) Action "Enable APB register write access" by address &910xFFFE2000&93 write value &910x00000260&93.
03) Act...
|
|
|
|
1 |
2484 |
by Deleted User04 Aug 2007 01:04 AM |
|
10 Replies and 2491 Views
Restoring Logic Loader 2491 10
Started by rrobbins6111
I am using the Rowley CrossStudio and CrossConnect. Everyting was going well until I tried to execute a program out of flash. Now whenever I try and do anything with the JTAG I get a message 'Cannot Stop Target', and I cannot load any of the .ELF files provided for restoring Logic Loader. Are there any specific instructions on how to do this or do you have any other suggestions
|
|
|
|
10 |
2491 |
by rrobbins611113 Jul 2007 12:49 AM |
|
0 Replies and 2008 Views
Problem in using I2c Bus 2008 0
Started by Deleted User
I am trying to interface a keyboard with the dev kit through the MAX7349 controller using the I2C module of the 79524.
I have taken connection form Expansion slot J38's pin 57 (MFP23,K2) as SCL and pin 58 (MFP24,K3) as SDA
I first wrote a small C program in Logic Loader but when I tried to access the MUXCTRL4 register to define I2C for the i/o pins, I get a segmentation fault. What am I doing wrong
So instead I tried to create a small module inside the Linux kernel. This is what I do inside t...
|
|
|
|
0 |
2008 |
16 Dec 2006 03:31 AM |
|
0 Replies and 2045 Views
I2C communication to external peripherals 2045 0
Started by gaspertom
Does anyone know of any sample code or library to communicate with external periphials using the I2C protocol via the GPIO pins
|
|
|
|
0 |
2045 |
30 Nov 2006 03:58 PM |
|
1 Replies and 2416 Views
CF Card not recognized 2416 1
Started by Deleted User
Hi,
Am trying to load linux using the CF card. However, when I try to detect the CF card on LoLo, I get the following errors.
losh> mount fatfs /cf
ata_wait_drq (1): bsy wait timeout 20279000 20283000
timeout resetting cf card
ata_wait err: 37
ata_wait err: 33
ata_wait err: 47
ata_wait err: 47
ata_wait err: 47
ata_wait err: 47
ata_wait_drq (0): bsy wait timeout 20295000 20300000
error: mount: failed to open (ATA)
I am using a Sandisk 128MB card which I formatted both as Fat and as ext2 and ...
|
|
|
|
1 |
2416 |
by 06 Oct 2006 03:17 PM |
|
5 Replies and 2551 Views
Fried LogicLoader 2551 5
Started by Deleted User
Hi,
I was trying to attempt to modify the Apex bootloader to boot over the network and somewhere issued a 'delete $env' command. Now the SDK can't seem to boot up.
I have a JTAG-ICE but that doesn't seem to work with the kit. Any ideas on how I can restore logic loader without using the Jtag interface
Thanks,
Joy.
|
|
|
|
5 |
2551 |
by 28 Sep 2006 09:15 AM |
|
1 Replies and 2510 Views
Booting over Network 2510 1
Started by Deleted User
Hello,
I do not have a compact flash card and wish to load linux over the network. The configuration that is used with the bsp assumes a compact flash card to be used for loading the kernel.
What would I need to do in order to accomplish booting over the lan network and not a compact flash card
Any help will be much appreciated.
Regards,
Joy.
|
|
|
|
1 |
2510 |
by 05 Sep 2006 10:39 AM |