Booting with TI UBL Device OPP (300MHz, 1.2V) U-Boot 2010.12 (Dec 23 2011 - 11:22:43) I2C: ready DRAM: 128 MiB MMC: davinci: 0 SF: Detected M25P64 with page size 256, total 8 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial ARM Clock : 300000000 Hz DDR Clock : 132000000 Hz SF: Detected M25P64 with page size 256, total 8 MiB Invalid MAC address read. Net: Ethernet PHY: GENERIC @ 0x00 DaVinci-EMAC Hit any key to stop autoboot: 0 reading boot.scr 248 bytes read ## Executing script at c0600000 reading uImage 2315152 bytes read ## Booting kernel from Legacy Image at c0700000 ... Image Name: Arago/2.6.37-psp03.21.00.04.sdk/ Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2315088 Bytes = 2.2 MiB Load Address: c0008000 Entry Point: c0008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Linux version 2.6.37 (a0876316@bangdvsdkdev01) (gcc version 4.3.3 (GCC) ) #1 PREEMPT Fri Dec 23 11:12:57 IST 2011 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: DaVinci DA850/OMAP-L138/AM18x EVM Memory policy: ECC disabled, Data cache writeback DaVinci da850/omap-l138/am18x variant 0x1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 24320 Kernel command line: console=ttyS2,115200n8 root=/dev/mmcblk0p2 rw ip=off mem=32M@0xc0000000 mem=64M@0xc4000000 rootwait PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 32MB 64MB = 96MB total Memory: 92492k/92492k available, 5812k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) DMA : 0xff000000 - 0xffe00000 ( 14 MB) vmalloc : 0xc8800000 - 0xfea00000 ( 866 MB) lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .init : 0xc0008000 - 0xc0032000 ( 168 kB) .text : 0xc0032000 - 0xc047e000 (4400 kB) .data : 0xc047e000 - 0xc04a8980 ( 171 kB) SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Preemptable hierarchical RCU implementation. RCU-based detection of stalled CPUs is disabled. Verbose stalled-CPUs detection is disabled. NR_IRQS:245 Console: colour dummy device 80x30 Calibrating delay loop... 149.50 BogoMIPS (lpj=747520) pid_max: default: 32768 minimum: 301 Security Framework initialized Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok DaVinci: 144 gpio irqs regulator: core version 0.5 regulator: dummy: NET: Registered protocol family 16 WARNING: both McASP and McBSP are enabled, but they share pins. Only McASP will work. If you want McBSP support, disable McASP. WARNING: both McASP and UART1_AFE are enabled, but they share pins. Disable one of them. da850_evm_init: eHRPWM module 0 cannot be used since it is being used by MII interface da850_evm_init: eHRPWM module1 outputA cannot be used since it is being used by LCD da850_evm_init: eHRPWM module1 outputB cannot be used since it is being used by spi1 bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pca953x 1-0020: failed reading register pca953x 1-0021: interrupt support not compiled in regulator: VDCDC1: 3200 <--> 3300 mV at 3300 mV regulator: VDCDC2: 1750 <--> 3300 mV at 3300 mV regulator: VDCDC3: 950 <--> 1350 mV at 1200 mV regulator: LDO1: 1800 mV regulator: LDO2: 1150 <--> 1300 mV at 1200 mV i2c-gpio i2c-gpio.1: using pins 20 (SDA) and 21 (SCL) Advanced Linux Sound Architecture Driver Version 1.0.23. Bluetooth: Core ver 2.15 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Switching to clocksource timer0_1 musb-hdrc: version 6.0, host, debug=0 musb-hdrc musb-hdrc: dma type: dma-cppi41 Waiting for USB PHY clock good... musb-hdrc musb-hdrc: MUSB HDRC host driver musb-hdrc musb-hdrc: new USB bus registered, assigned bus number 1 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected musb-hdrc musb-hdrc: USB Host mode controller at fee00000 using DMA, IRQ 58 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. EMAC: MII PHY configured, RMII PHY will not be functional McBSP:Probed McBSP1 JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. msgmni has been set to 180 io scheduler noop registered (default) da8xx_lcdc da8xx_lcdc.0: GLCD: Found Sharp_LK043T1DG01 panel Console: switching to colour frame buffer device 60x34 Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x1c42000 (irq = 25) is a AR7 serial8250.0: ttyS1 at MMIO 0x1d0c000 (irq = 53) is a AR7 serial8250.0: ttyS2 at MMIO 0x1d0d000 (irq = 61) is a AR7 console [ttyS2] enabled brd: module loaded at24 1-0050: 32768 byte 24c256 EEPROM (writable) ahci ahci: forcing PORTS_IMPL to 0x1 ahci ahci: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode ahci ahci: flags: ncq sntf pm led clo only pmp pio slum part ccc scsi0 : ahci_platform ata1: SATA max UDMA/133 mmio [mem 0x01e18000-0x01e19fff] port 0x100 irq 67 spi_davinci spi_davinci.1: DMA: supported spi_davinci spi_davinci.1: DMA: RX channel: 18, TX channel: 19, event queue: 0 m25p80 spi1.0: m25p64 (8192 Kbytes) Creating 6 MTD partitions on "m25p80": 0x000000000000-0x000000010000 : "UBL" 0x000000010000-0x000000090000 : "U-Boot" 0x000000090000-0x0000000a0000 : "U-Boot-Env" 0x0000000a0000-0x000000320000 : "Kernel" 0x000000320000-0x000000720000 : "Filesystem" 0x0000007f0000-0x000000800000 : "MAC-Address" Read MAC addr from SPI Flash: ff:ff:ff:ff:ff:ff spi_davinci spi_davinci.1: Controller at 0xfef0e000 davinci_mdio davinci_mdio.0: davinci mdio revision 1.5 davinci_mdio davinci_mdio.0: detected phy mask fffffffe davinci_mdio.0: probed davinci_mdio davinci_mdio.0: phy[0]: device 0:00, driver SMSC LAN8710/LAN8720 console [netcon0] enabled netconsole: network logging started ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci ohci.0: DA8xx OHCI ohci ohci.0: new USB bus registered, assigned bus number 2 Waiting for USB PHY clock good... ohci ohci.0: irq 59, io mem 0x01e25000 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. input: gpio-keys-polled as /devices/platform/gpio-keys-polled.1/input/input0 input: TPS6507x Touchscreen as /devices/platform/i2c-gpio.1/i2c-1/1-0048/input/input1 omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0 ata1: SATA link down (SStatus 0 SControl 300) omap_rtc: RTC power up reset detected i2c /dev entries driver watchdog watchdog: heartbeat 60 sec Bluetooth: HCI UART driver ver 2.2 Bluetooth: HCI H4 protocol initialized Bluetooth: HCILL protocol initialized cpuidle: using governor ladder cpuidle: using governor menu davinci_mmc davinci_mmc.0: Using DMA, 4-bit mode davinci_mmc davinci_mmc.1: Using DMA, 4-bit mode usbcore: registered new interface driver usbhid usbhid: USB HID core driver 1-0018 supply IOVDD not found, using dummy regulator 1-0018 supply DVDD not found, using dummy regulator 1-0018 supply AVDD not found, using dummy regulator 1-0018 supply DRVDD not found, using dummy regulator asoc: tlv320aic3x-hifi <-> davinci-mcasp.0 mapping ok ALSA device list: #0: DA850/OMAP-L138 EVM nf_conntrack version 0.5.0 (1445 buckets, 5780 max) ip_tables: (C) 2000-2006 Netfilter Core Team TCP cubic registered NET: Registered protocol family 17 Bluetooth: L2CAP ver 2.15 mmc0: new high speed SDHC card at address b368 Bluetooth: L2CAP socket layer initialized Bluetooth: SCO (Voice Link) ver 0.6 Bluetooth: SCO socket layer initialized mmcblk0: mmc0:b368 NCard 3.73 GiB mmcblk0: p1 p2 Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM socket layer initialized mmcblk0: p2 size 3261195 extends beyond EOD, truncated Bluetooth: RFCOMM ver 1.11 Bluetooth: BNEP (Ethernet Emulation) ver 1.3 Bluetooth: BNEP filters: protocol multicast Bluetooth: HIDP (Human Interface Emulation) ver 1.2 regulator_init_complete: incomplete constraints, leaving LDO2 on regulator_init_complete: incomplete constraints, leaving LDO1 on regulator_init_complete: incomplete constraints, leaving VDCDC3 on regulator_init_complete: incomplete constraints, leaving VDCDC2 on regulator_init_complete: incomplete constraints, leaving VDCDC1 on davinci_emac_probe: using random MAC addr: 06:6b:86:99:28:38 omap_rtc omap_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) EXT3-fs: barriers not enabled kjournald starting. Commit interval 5 seconds EXT3-fs (mmcblk0p2): using internal journal EXT3-fs (mmcblk0p2): recovery complete EXT3-fs (mmcblk0p2): mounted filesystem with writeback data mode VFS: Mounted root (ext3 filesystem) on device 179:2. Freeing init memory: 168K INIT: version 2.86 booting Please wait: booting... Starting udev udevd (606): /proc/606/oom_adj is deprecated, please use /proc/606/oom_score_adj instead. udev: starting version 141 Remounting root file system... Caching udev devnodes Populating dev cachemv: cannot rename '/tmp/devices': No such file or directory NET: Registered protocol family 10 logger: mount: mount point /proc/bus/usb does not exist ALSA: Restoring mixer settings... Configuring network interfaces... Found hardware: "" "" "" "" "" Hardware is initialized using a generic method /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #3 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #4 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #5 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #6 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #7 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #8 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #9 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #11 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #12 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #13 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #15 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #16 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #17 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #18 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #19 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #21 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #22 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #23 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #24 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #29 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #30 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #31 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #32 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #33 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #34 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #35 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #36 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #37 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #38 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #39 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #40 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #41 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #42 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #43 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #44 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #45 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #46 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #47 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #48 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #49 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #50 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #51 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #52 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #70 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #71 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #72 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #73 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #74 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #77 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #78 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #79 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #80 (No such file or directory) /usr/sbin/alsactl: set_control:1267: failed to obtain info for control #81 (No such file or directory) davinci_mdio davinci_mdio.0: resetting idled controller net eth0: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=0:00, id=7c0f1) ADDRCONF(NETDEV_UP): eth0: link is not ready net eth0: DaVinci EMAC: ioctl not supported eth0 no wireless extensions. udhcpc (v1.13.2) started Sending discover... PHY: 0:00 - Link is Up - 100/Full ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Sending discover... Sending select for 192.168.120.78... Lease of 192.168.120.78 obtained, lease time 86400 adding dns 10.1.2.138 adding dns 10.1.2.139 done. Setting up IP spoofing protection: rp_filter. Fri Dec 23 12:42:00 UTC 2011 INIT: Entering runlevel: 5 Starting system message bus: dbus. Starting Dropbear SSH server: dropbear. Starting telnet daemon. Starting network benchmark server: netserver. Starting syslogd/klogd: done Starting thttpd. CMEMK module: built on Dec 23 2011 at 12:04:44 Reference Linux version 2.6.37 File /datalocal/DVSDK43_HPDL380G7/arago-tmp/work/da850-omapl138-evm-arago-linux-gnueabi/ti-linuxutils-1_2_26_02_05-r57d/linuxutils_2_26_02_05/packages/ti/sdo/linuxutils/cmem/src/module/cmemk.c CMEM Range Overlaps Kernel Physical - allowing overlap CMEM phys_start (0xc2000000) overlaps kernel (0xc0000000 -> 0xc6000000) allocated heap buffer 0xc9000000 of size 0x1200000 heap fallback enabled - will try heap if pool buffer is not available cmemk initialized DSPLINK Module (1.65.01.05_eng) created on Date: Dec 23 2011 Time: 12:07:46 Calibrating touchscreen (first time only)xres = 480, yres = 272 Took 11 samples... Top left : X = 137 Y = 784 Took 9 samples... Top right : X = 896 Y = 771 Took 12 samples... Bot right : X = 905 Y = 217 Took 9 samples... Bot left : X = 129 Y = 210 Took 11 samples... Center : X = 525 Y = 506 -16.710449 0.495008 0.000198 288.236511 -0.001111 -0.304784 Calibration constants: -1095136 32440 12 18889868 -72 -19974 65536 . Starting Matrix GUI application. _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org arago ttyS2 Arago 2011.06 arago ttyS2 arago login: